- Digitech rpx400 pro tracks software install#
- Digitech rpx400 pro tracks software drivers#
- Digitech rpx400 pro tracks software driver#
- Digitech rpx400 pro tracks software pro#
- Digitech rpx400 pro tracks software software#
This time click Yes and your computer will restart. You DO NOT need to restart your computer yet.
![digitech rpx400 pro-tracks software digitech rpx400 pro-tracks software](https://m.media-amazon.com/images/I/71XwmM2bjoL._AC_SL1500_.jpg)
Connect the RPx400 to the computer with the included USB cable. Click Next and Windows will display the following message:Ħ 5.Click Yes and you will see the same window appear one more time.
Digitech rpx400 pro tracks software drivers#
Select USB Audio MIDI Drivers from the menu that appears. The installation menu should automatically appear (if installation does not start automatically, go to Start>Run, click on Browse, type d:\instmenu.exe (where d:\ is your CD-ROM drive), and click OK. Put the X-Edit CD into your CD-ROM drive. Make sure you DO NOT have the RPx400 USB plugged into your computer. Windows 2000 Users NOTE: DO NOT connect the RPx400 to your Windows 2000 computer until AFTER the DigiTech USB drivers are installed or it may cause instability in Windows.
Digitech rpx400 pro tracks software driver#
The RPx400 USB driver installation is now complete. Click Continue Anyway and you will see: 14. Click Continue Anyway and you will see:ĥ 13. Click Continue Anyway and you will see: 12. Click Continue Anyway and you will see:Ĥ 11. If the RPx400 is connected correctly to the computer you will see the following message from Windows: 10. NOTE: If you don t have the USB cable connected to the RPx400 you will see this: If you see this message, cancel the installation and connect the USB cable to the RPx400 then restart the installation and begin with Step 1 of this section. Installation of the drivers could take several minutes. You will see the following window appear: 8. Now select USB Audio MIDI Drivers from the menu. The installation menu shouldģ automatically appear (if installation does not start automatically, go to Start>Run, click on Browse, type d:\instmenu.exe (where d:\ is your CD-ROM drive), and click OK.
Digitech rpx400 pro tracks software software#
Put the X-Edit software CD into your CD-ROM drive. however, installation of the software IS NOT complete. When the message "Your new hardware is installed and ready to use" appears,windows has completed identifying your new hardware. Wait until Windows has found and identified all of the USB devices from the RPx400. There are multiple messages because there are four USB devices in the RPx400, two MIDI devices and two audio devices. Connect the included USB cable to your computer and to the RPx You will see multiple messages pop up from the task bar indicating that your computer has found a new USB device.
![digitech rpx400 pro-tracks software digitech rpx400 pro-tracks software](https://www.digitech.com/on/demandware.static/-/Sites-masterCatalog_Harman/default/dw1738ac88/RPx400_large.png)
Remove the USB Warning sticker covering the RPx400 s USB port. Take the RPx400 out of the box and plug the power in. Follow the directions in the section that applies to your operating system. There are different installation procedures for Windows XP users and Windows 2000 users.
![digitech rpx400 pro-tracks software digitech rpx400 pro-tracks software](https://media.musiciansfriend.com/is/image/MMGS7/RPx400-Modeling-Floor-Processor-and-USB-Interface/150843000000000-00-500x500.jpg)
Digitech rpx400 pro tracks software install#
Installing DigiTech USB Drivers You must install the USB drivers to use the RPx400 s USB connection with your computer.
Digitech rpx400 pro tracks software pro#
Click Exit from Pro Tracks Installation screen. When the Installation Complete window appears deselect Launch Pro Tracks and Read Me check boxes and click Finish. Click Install Pro Tracks to start installation again. NOTE: If you exit Setup without completing the installation, choose Start>Run, type d:\autorun.exe (where d:\ is your CD-ROM drive), and click OK. If DirectX is installed at this time, you will need to restart your computer and return to Step 1.
![digitech rpx400 pro-tracks software digitech rpx400 pro-tracks software](http://3.bp.blogspot.com/-jC1aPPnBejI/UTYIX0rY1UI/AAAAAAAAEeY/HyegMdtiHEo/s1600/Magix+Movie+Edit+Pro+17+Plus+2.png)
If DirectX 8.1+ is not installed, the installer will automatically install it for you. Click the Install Pro Tracks button and follow the installation instructions on the screen. If the menu does not appear automatically, you can open it by selecting Start>Run and entering d:\autorun.exe (where d:\ is the letter of your CD-ROM drive). If you have autorun enabled, the Pro Tracks installation menu opens automatically, showing you several buttons. Place the Pro Tracks CD-ROM in your CD-ROM drive. Close any open programs you have running. Please follow these instructions carefully to ensure smooth installation of each of these components. This installation guide contains the information to install the required USB drivers, X-Edit editor/librarian and Pro Tracks recording software for use with the RPx400. Visit our software page if you don't have the sound librarian installed yet.1 RPx400 USB Drivers and Software Installation GuideĢ Congratulations on your purchase of a DigiTech RPx400. Get started with these famous tones by connecting your GSP or RP unit to your Mac or PC.